Jeff Rowland Capri S2-SC Preamplifier

Code
£0.00
£6,350.00
Code
£0.00
£6,350.00
Save
Earn 0 reward points with this product.
  • Description

    Jeff Rowland Capri S2-SC Preamplifier

    The Capri S2-SC features an impressive complement of standard input/output interfaces; greatly enhanced flexibility through its phono card options; and the Rowland trademark prismatic platinum faceplate beautifully integrated into a non-resonant chassis milled from a solid block of aluminum.

    With an output impedance of only 80 Ohms balanced and 40 Ohms single ended, Capri S2-SC drives any amplifier with confidence. Whether serving a single-ended triode amplifier in a vinyl rig, or controlling a quartet of solid-state Rowland amplifiers or at the nexus of a home theater setup, the Capri S2-SC preamplifier delivers the trademark Rowland musicality, resolution, and consistent authority.

    Features

    Compact elegance

    Balanced preamplifier design housed inside a low profile, compact, ultra-low resonance, structurally rigid chassis that is precision-machined from solid blocks of aircraft grade 6061-T6 aluminum that is completely sealed for trouble-free operation and high RF and EMI isolation. Features an elegant front panel precision-machined and sculpted with a diamond tipped cutting tool.

    Universal power supply

    Low noise, high-current, dual regulated switch- mode auto sensing and auto ranging power supply provides Capri with optimum performance at any world-wide mains operating voltage.

    Thin-Film Resistors

    All resistors are low noise, 0.1% thin-film type for extremely low thermal noise which complement the low-noise characteristics of the active circuitry.

    Four-Layer Circuit Board

    All circuitry is populated on one side of a 4 layer circuit board to allow for continuous, unbroken, low impedance ground and power supply distribution planes. Care was taken to minimize signal path lengths and components sizes.

    Input transformer-Coupling and Isolation

    Transformer coupled input circuitry provides universal component compatibility and virtually eliminate ground loop noise and RFI/EMI. Transformer coupling ensures identical preamplifier overall gain when using unbalanced input adapters. Other benefits include ground noise isolation and excellent common mode noise rejection (CMRR) from all sources.

    I/O flexibility

    Dual low impedance line-level outputs (80 Ohms balanced, 40 Ohms unbalanced), 48 Ohms balanced and unbalanced inputs, and preamp bypass inputs allow unprecedented compatibility with audio and A/V components, while optional high quality phono cards are available for compatibility with vinyl sources.

    Remote control

    Six-function remote control transmitter display dim, adjusts volume, input selection, mute, phase, and channel balance.

    Precision volume adjustments

    Dual rate volume control allows precision level adjustments over nearly a 100 dB range. The volume control incorporates a permanently noiseless optical encoder that always maintain its tactile feel, accuracy, and channel balance at all settings. The optical encoder mounted behind the volume knob commands the attenuation level of a monolithic resistor attenuator over a 99.5 dB range in 0.5 dB increments.

    Optional Phono Cards

    Plug-in Standard phono cards (installed internally) converts Line Input 1 to high performance phono input. Three gain and loading options can accommodate moving magnet (MM), moving coil (MC), and high output moving coil cartridge types. OR the HP (High Performance) cards can be installed for a high performance MC with input transformer with many load options.

    Home Theater Bypass Adjustment

    The Home Theatre BYPASS RCA inputs can be changed to an additional set of standard inputs by placement of an internal jumper inside the unit.

    Display Off (5 Sec)

    An internal jumper will place the display in an automatic OFF condition after 5 seconds from any operational command and illuminates again for 5 seconds after additional commands are initiated.

    High-quality connectors

    All signal connectors are rhodium plated, copper jacks (RCA) and Neutrix silver plated contact (XLR), soldered directly to the circuit board for direct connection to the signal circuitry.

    Green technology

    Modest power consumption of mere 6 Watts permits constant power-up operation to eliminate warm-up time and maximize musical performance, and allows Capri to operate enclosed into an entertainment unit.

    IEC

    15 Amp female IEC AC power connector.

    Specifications

    Overall Gain

    14 dB

    Gain Range

    99.5 dB, 199 Equal Increments

    Frequency Response

    10 Hz – 350 kHz, -3 dB

    Phono Card (optional)

    Adjustable for simple load and gain adjustments for MM, high-output MC and MC cartridges

    Inputs

    2 x Pair Balanced XLR, 1 x Pair Unbalanced (RCA) Unity Gain (Bypass), 2 x Pair Unbalanced RCA

    Outputs

    1 x Pair Balanced Line Level, 1 x Pair Unbalanced Line Level

    Weight

    9.5 lbs / 4.26 kg

    Dimensions

    2.6”(H) x 13.7” (W) x 6.2” (D) / 6.7 cm (H)x 35 cm (W) x 15.7 cm (D)


  • Reviews (0)

    Be the first to review this product.


    Leave your own review